The stature that Diablo Controls has achieved with its innovative and effective products, is a result of a clear understanding of the gate automation and traffic industry.
Probe Kits do away with conventional loops. New technology has made digging circular trenches in the ground obsolete. Vehicle Sensors have created for efficient and intelligent installation.
VD909 “Dynamite” Free Exit Sensor
The Dynamite (VD909) is a quicker and simpler to fit, hi-tech alternative, to standard inductive loop detectors in free exit applications.
VD959 “Adjustable Dynamite” Free Exit Sensor
Adjustable version of the VD909 kit, requires a RK-1R board for basic installations.Designed for gate installations (including solar and battery operated). Pulse technology for use in free exit/free entry applications. Requires no loops to be cut, sensor does the work of the loops
VD913 “TRIAD” Tri-Axis Magnetometer
The system is comprised of two parts, a master unit (VD913D) with adjustable sensitivity settings and the sensor (VD913S). The advanced sensor’s small size and high sensitivity make it ideally suited to vehicle detection applications. It is mounted on a 10pin Molex connector.
VD960 “Magna” Presence Vehicle Sensor
The VD960 is a stand alone digital Presence sensor. Magnas recognise vehicles by their ferrous content such as tyres, engine and suspension components. All parameters are self setting to suit site conditions. Mounted in the middle of the road below ground level.
VD970 “MagnaPass” Free Exit Vehicle Sensor
The VD970 is a stand alone digital Free exit sensor. MagnaPass is mounted on the side of the road so there is no need for any ground work. It is self adjusting so there is no need for a controller. The digital output means you can wire directly to the control panel up to 100m.
Commonly used in both the gate automation and traffic industry, plug in detectors require a pinned base in which to mount the detector inside the control panel. These detectors work with traditional loops that are cut into the ground.
VD940 Standard Loop Detector
The VD940 has 4 levels of sensitivity which may be changed. At last a plug-in detector that will operate on any voltage from 10 to 30 volts AC or DC. It has been specifically designed to handle parking, drive-through and access control applications where solid-state outputs are required for both the detect and fail outputs. The detector loop inductance should be between 20 and 2000 microhenries.
VD950 Sensitivity Adjustable Detector
The VD950 detector will add a new dimension of simplicity to your plug-in detector requirements as it can operate as a loop detector but with the flip of a switch it can operate our probe in pulse mode. This detector operates on any voltage from 10 to 30 volts AC or DC.
VD911 11-pin traffic detector
Available with the industry standard 11-pin base. This micro-sized detector will automatically adjust its sensitivity level when used on different sized loops. The detector loop inductance should be between 20 and 2000 microhenries.
VD921 11-pin 2channel Detector
The VD921 Series Detector was developed for systems that need accurate vehicle count information. This detector is designed to operate utilizing a dual inductive loop configuration typical in the parking industry. The small packaging comes without sacrificing performance.
The Low-Power Workhorse! The VD906 & 7, or Dinky, vehicle detector has been specifically designed for solar powered gate applications as well as conventional powered systems. This detector will operate on any voltage from 10 to 30 Volts AC or DC and draws approximately 1 milliampere while waiting for a car. This micro-sized detector will automatically adjust its sensitivity level when used on different sized loops. Environmental conditions are constantly compensated with the Diablo HYPERTRACK software.
VD906 "Fail Safe" Loop Detector
VD906 Fail Secure: when a fault in the system is detected the VD906 will alert the gate control panel to remain closed and secure. The gate and the property will remain closed until the fault is rectified, making it ideal for safety applications.
VD907 "Fail Secure" Loop Detector
VD907 Fail Safe: when a fault in the system is detected the VD907 will alert the gate control panel to remain closed and secure. The gate and the property will remain closed until the fault is rectified, making it ideal for safety applications.
Want to know more about fitting loops?
Below are some guides to help you.